Let’s suppose that it is the middle of July, probably the hottest day of the years and suddenly, your AC stops to work at all. What options do you think you have? Well, most people will panic and search for the AC technicians in Indian Wells CA, right? Well, if you consider yourself a DIY fanatic and have the right tools of the trade, you can easily tackle the project on your own as well. Trust us, you will be saving yourself a few hundred dollars and even repair your AC system.
Note: Keep in mind that you’ll be dealing with electricity and high-pressure refrigerant. If you are not comfortable with either of these, it is highly recommended that you err on the side and hire a professional for the job.
All in all, there are a lot of reasons that can cause your AC to stop functioning. And you shouldn’t have to worry about it because in this article, we’ll be talking about the most common types of issues that can happen at any time of the day or night, yet you can easily take care of it on your own.
Methods and Techniques Of AC Repair
Some of the most common reasons for AC problems are:
- Plugged Air Filter
- Lack Of Air Returning
- Plugged Condenser Fan
- Failed Capacitor
- Failed Contactor
Below we’ve managed to mentioned list the techniques to repair the above-listed AC issues. So, it is requested that you read this article until the end to get the most out of it.
Plugged Air Filter
Well, the plugged air filter and evaporator coil is one of the top issues of AC. Keep in mind that if you have pets at home such as cats, and dogs, there is a high chance that you’ll be facing this issue.
First of all, you need to shut the main power supply of the furnace and find the air filter location. Pull it out and then purchase a new one of the same rating and size.
Once you replace the filters, you need to ensure that it is pointing in the right direction. Now turn on the furnace and check if the issue has been resolved.
Lack Of Air Returning
This has to be one of the hardest to track down, however that is on the grounds that it is in a real sense avoiding you. This is because the evaporator curl, which is usually the indoor components of your AC, normally situated over your heater, needs a wind stream to ingest warmth from the air, and in the event that it does not get that wind stream, it will form ice and stop working instantly.
The primary spot you inspected was the filter, yet it’s alright, so what next? Your house AC system has two kinds of vents, release vents and returns air vents. Presently ensure that none of the vents are obstructed or even covered. They should be clear on the grounds that the entire AC system is intended to take in a specific volume of air.
Plugged Condenser Fan
In the event that you’ve made it this far, you’re not just drawing near to sorting out the issue with your cooling framework, but on the other hand, you’re guaranteeing that it will be working all the more productively pushing ahead. Since your AC system is the greatest purchaser of energy in your house, you’ll currently be setting aside cash.
Alright, so we should verify whether you’re condenser loop is stopped. On the off chance that you’ve never cleaned, at that point, it’s in any event messy and should be cleaned. So, how about you do that now?
Hose down the exterior coil, you’ll have to ensure that you are pointing the splash directly at the loop and not on a point. In the event that you wind up twisting the loop balances, you’ll accomplish more damage than good.
Failed Capacitor
Remove the capacitor from the holding section, and afterward take a protected screwdriver and contact it between the COMMON (or “C”) terminal and the HERM (or “H”) terminal. Do likewise between the “C” terminal and the FAN (or “F”) terminal. For single-mode capacitors, you should simply make a short between the two terminals.
If you feel that you are not capable of doing such a task, you can always search for a residential HVAC specialist. There is no shame in hiring them.
Failed Contactor
How about we decide whether the condenser fan has fizzled. You have to ensure that your indoor regulator is set to cool and that the temperature setting is also turned down. Now that you’ve turned the power on for your heater and your open-air unit, at that point you have to affirm that the outside unit is gaining the signal of the power.
There are a few different methods to do this; you could remove the control board on the gathering unit, which you may need to do later at any rate, and use the multimeter to affirm that the contactor is getting “pulled in” in the right way.
